12 10/100TX D-coded L2+ (8 PoE at/af) Managed Ethernet Switch w/ enhanced G.8032 Ring ; 24V model

  • EN61373 verification: 24V Input voltage
  • E-mark certificate for vehicle
  • IEEE802.3at/af up to 30W per port; PoE management incl. detection and scheduling (For PoE Model)
  • Enhanced G.8032 ring protection < 20ms for single ring. Supports auto mode, enhanced mode, train mode, multi-VLAN and basic mode; Enhanced G.8032 ring covers multicast packets; MSTP 16MSTI /RSTP; support MRP ring
  • Environmental Monitoring for temp., voltage and total PoE load and current
  • Miss-wiring avoidance & node failure protection
  • Support LACP link aggregation, IGMP v3/router port, MLD snooping, DHCP server & DHCP Option82; Port based DHCP distribution, Mac based DHCP server, QoS by VLAN, SSH v2/SSL, HTTPS, INGRESS/EGRESS ACL L2/L3, TACACS+**, QinQ of VLAN
  • Protocol based VLAN; IPv4 Subnet based VLAN
  • N-key configurator** for upgrading, auto/editable configuration back up and restoration without computer
  • IP54/67 housing; User friendly UI, including auto topology drawing; Complete CLI
  • Compliant with ISO 7637-2
  • ITxPT labeled w/ignition function , delay shut down , standby green mode , Inventory service
  • POE Off/Timer on ignition standby mode
  • Optional bypass in case of power failure (IP67 only)


ITU G.8032 Ring Environmental Monitoring PoE 802.3at/af 30W ITxPT
FCC CE WEEE RoHS2 EN50155 EN45545-2  Fire & Smoke


Datasheet   Hardware Manual  
For latest firmware and web UI user manual, please contact us.

OVERVIEW

Lantech I(P)ES-5408T-D-IGN is a high performance L2+ Ethernet switch with 12 10/100TX (D-coded) w/8 PoE 802.3af/at ports by M12 provides L2 wire speed and advanced security function for network aggregation deployment. It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring while also supports train ring, enhanced mode, multiple VLAN mode with easy configuration. The comprehensive QoS by VLAN, advanced security including INGRESS/EGRESS ACL L2/L3, TACACS+**, SSH v2/SSL and Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port, QinQ are also supported and required in large network. It also supports Cisco Discovery Protocol (CDP) for Ciscoworks to detect the switch info and show on L2 map topology.


Up to 8 PoE ports with advanced PoE management (For PoE Model)
Lantech IPES-5408T-D-IGN supports IEEE802.3at/af standard which can feed HI-power up to 30W at each PoE port for big power consumption devices like PTZ IP camera, High power wireless AP etc. The advanced PoE management includes PoE detection and scheduling besides the regular PoE per port status. PoE detection can detect if the connected PD hangs then restart the PD; PoE scheduling is to allow pre-set power feeding schedule upon routine time table. Per port PoE status can remotely On/Off the power and display information of voltage, current, watt and PoE temperature.


E-marking certificate, ITxPT; ISO 7637-2 compliant and extended working temperature
The I(P)ES-5408T-D-IGN is designed to meet with critical network environment with IP54/67 enclosure and M12 connectors for protection against dust and water. It has passed harsh environmental testing to comply with Industrial EMI and Safety standards as well as stability testing such as Free fall, Shock, and vibration. It is labeled with ITxPT public transport standards and also compliant with ISO 7637-2 which protects switch from being damaged by high voltage that could be found at vehicle cranky start. For a greater flexibility in application the I(P)ES-5408T-D-IGN supports an extended operating temperature range from -40°C to 75°C. The E-marking certificate makes it the most suitable switch for bus, carriage, other vehicles application as well as for industrial areas where the power source is limited with 24V but has demand of IP surveillance or VoIP applications.


Dual power input design (24V input)
The Lantech I(P)ES-5408T-D-IGN is designed with dual power which can accept 9V~36VDC. Featured with relay contact alarm function, the I(P)ES-5408T-D-IGN being able to connect with alarm system in case of power failure or port disconnection events.


Miss-wiring avoidance, Loop protection, Node failure protection
The I(P)ES-5408T-D-IGN also embedded several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech I(P)ES-5408T-D-IGN being able to alert with the LED indicator and disable ring automatically. Node failure protection ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.


DHCP option 82 & Port based, Mac based DHCP, Option66, IPv6 DHCP server
DHCP server can assign dedicated IP address by MAC or by port (Port based for single switch), it also can assign IP address by port for multiple switches with single DHCP option82 server. For the ending device which need to download file from TFTP server, DHCP Option66 server can offer IP address of TFTP server to DHCP client. Basic IPv6 DHCP service can be supported.


Auto-provisioning for firmware/configuration update
The switch supports auto-provisioning for switch to auto-check the latest software image and configuration through TFTP server.


User friendly UI, Auto topology drawing, complete CLI
The user-friendly UI, innovative auto topology drawing and topology demo makes I(P)ES-5408T-D-IGN much easier to get hands-on. The complete CLI enables professional engineer to configure setting by command line.


Enhanced G.8032 ring; 16 MSTI MSTP; MRP ring
Lantech I(P)ES-5408T-D-IGN features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering Multicast packets. It also supports various ring topologies that covers double ring, multi-chain (under enhanced ring), train ring, basic ring, multiple-VLAN ring and auto-ring by easy setup than others. The innovative auto-Ring configurator (auto mode) can calculate owner and neighbor in one step. It supports MSTP that allows each spanning tree for each VLAN for redundant links with 16 MSTI. MRP (Media Redundancy Protocol) can be supported for industrial automation networks.


QoS by VLAN for legacy devices to tag with priority
QoS by VLAN can allow switch to tag QoS by VLAN regardless the devices acknowledge QoS or not in which greatly enhance the bandwidth management in a network.


QinQ and GVRP supported
It supports the QinQ, GVRP for large VLAN segmentation.


802.1X security by MAC address
MAC-based port authentication is an alternative approach to 802.1x for authenticating hosts connected to a port. By authenticating based on the host's source MAC address, the host is not required to run a user for the 802.1x protocol. The RADIUS server that performs the authentication will inform the switch if this MAC can be registered in the MAC address table of switch.


IGMPv3, GMRP, router port, MLD Snooping, static multicast forwarding and multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP, router port, MLD snooping and static multicast forwarding binding by ports for video surveillance application.


Editable configuration file; Optional N-key auto backup, Exported text file
The configuration file of Lantech I(P)ES-5408T-D-IGN can be exported in text file so that it can be edited and configured back to switch with ease for mass deployment. The optional N-key configurator offers firmware upgrade, auto/editable configuration back up and restoration without computer by adjusting the DIP switch.


Event log & message; 1 DI + 1 DO
In case of event, the I(P)ES-5408T-D-IGN being able to send an email** to pre-defined addresses as well as SNMP Traps out immediately. It provides 1DI and 1DO. When disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the alarm while sending alert information to IP network with email and traps.


Optional bypass relay prevent from power lost (IP67 only)
The optional bypass relay is set to bypass the switch to the next one when power is off in order to protect the network from crashing. Lantech bypass caters to remain in bypass mode until the switch is completely booting up when power is back to avoid another network lost. Smart bypass can be activated when switch encounters power failure. (-BT/-BBT model)


Built-in environmental monitoring to show switch inside info
The built-in environmental monitoring can detect switch overall temperature, voltage total PoE load, and current where can send the SNMP traps, email** alert when abnormal.


ITXPT label for delay shut down, inventory service, standby green mode; POE off/Timer on ignition standby mode
When the engine of vehicle turns off, the switch is able to extend the work from 30sec to 60mins. The switch is able to provide SRV and TXT record back to office, and exports the data in xml file format. The consumption power under sleep mode meets the standard of ITxPT. POE Off/Timer function on ignition standby mode can ultimate the battery standby time by connecting essential devices.


EN61373 verification; High ESD protection
Lantech I(P)ES-5408T-D-IGN features high reliability and robustness coping with extensive EMI/RFI phenomenon, environmental vibration and shocks usually found in factory, substation, steel automation, aviation, mining and process control. It is the best solution for Automation, transportation, surveillance, Wireless backhaul, Semi-conductor factory and assembly lines. The I(P)ES-5408T-D-IGN is designed to meet with critical network environment with IP54 aluminum enclosure and M12 connectors for water proof. For more usage flexibilities, I(P)ES-5408T-D-IGN supports wide operating temperature from -40°C to 75°C.


*Future release
**Optional

FEATURES

  • 12 10/100TX (D-coded) IP54/67 M12 w/8 PoE 802.3af/at ports Managed Ethernet Switch (Total 12 Ports Ethernet Switch)
  • EN61373 shock/vibration verification
  • 24V model can accept dual 9~36VDC power input and boost to 54V for PoE 802.3at/af max 80W budget (For PoE Model)
  • Galvanic isolation from power input/Ethernet ports to system 1.5KV
  • N-key** configurator for firmware upgrade, auto/editable configuration back up and restoration
  • Back-plane (Switching Fabric): 2.4Gbps
  • 16K MAC address table
  • 10KB Jumbo frame
  • User friendly UI, auto topology drawing, topology demo, complete CLI for professional setting
  • Enhanced G.8032 Ring protection in 20ms for single ring
    • Support various ring/chain topologies, including train ring, enhanced ring, basic ring, auto ring & multiple VLAN ring
    • Enhanced G.8032 ring configuration with ease
    • Auto ring configuration (auto mode) for single ring
    • Cover multicast and data packets protection
  • Supports IEEE 802.1p Class of Service, per port provides 8 priority queues Port base, Tag Base and Type of Service Priority
  • IEEE 802.1d STP, IEEE 802.1w RSTP,802.1s MSTP VLAN redundancy with 16 MSTI
  • 4K 802.1Q VLAN, Port based VLAN, GVRP, QinQ of VLAN, QoS
  • Supports IEEE 802.1ab LLDP, Cisco CDP; LLDP info can be viewed via Web/ Console
  • MLD Snooping for IPv6 Multicast stream
  • DHCP server / client / DHCP Option 82 relay / DHCP
  • Option 82 server; Port based DHCP server; DHCP Option 66; basic IPv6 DHCP server
  • Mac based DHCP server to assign IP address that includes dumb switches in DHCP network
  • Bandwidth Control
    • Ingress packet filter and egress rate limit
    • Broadcast/multicast packet filter control
  • Relay alarm output system events
  • Miss-wiring avoidance
    • LED indicator
  • Node failure protection
    • Ensure the switches in a ring to survive after power breakout is back
    • The status can be shown in NMS when each switch is back
  • TFTP/HTTP firmware upgrade
  • System Event Log and SNMP Trap for alarm support; 32 RMON counters
  • Security
    • SSL/SSH v2/INGRESS/EGRESS ACL L2/L3
    • MAC address table: MAC address entries/Filter/MAC-Port binding
    • IP Security: IP address security management to prevent unauthorized intruder.
    • TACACS+**
    • Login Security: IEEE802.1X/RADIUS
    • HTTPS for secure access to the web interface
  • Static multicast forwarding forward reversed IGMP flow with multicast packets binding with ports for IP surveillance application
  • IGMP router port to assign query in ring for reversed multicast video flow
  • IGMPv1, v2, v3 with Query mode for multimedia; GMRP
  • Diagnostic including Ping / ARP table / DDM information
  • Watchdog design to auto reboot switch CPU is found dead
  • Built-in environmental monitoring for system input voltage, current, ambient temperature
  • Supports 1DI + 1DO (Digital Input/Digital Output)
  • IP54/67 aluminum housing with DIN rail** and wall mount design
  • E-mark certificate for vehicle
  • ISO7637-2 Level III compliant
  • ITxPT labeled w/ ignition function
    • Delay shut down
    • Inventory service
    • Standby green mode
  • POE off/Timer on ignition standby mode
  • Configuration backup and restoration
    • Supports editable configuration file for system quick installation
    • N-key** for mass configuration auto-backup, editable restoration and auto firmware upgrade
*Future release
**Optional

SPECIFICATIONS

Hardware Specifications

Standards

IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX
IEEE802.3ab 1000Base-T
IEEE802.3x Flow Control and Back Pressure
IEEE802.3ad Port trunk with LACP
IEEE802.1d Spanning Tree
IEEE802.1w Rapid Spanning Tree
IEEE802.1s Multiple Spanning Tree
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
IEEE 802.1X User Authentication (Radius)
IEEE802.1p Class of Service
IEEE802.1Q VLAN Tag
IEEE802.3at/af Power over Ethernet (For PoE Model)

Switch Architecture

Back-plane (Switching Fabric): 2.4Gbps

Transfer Rate

14,880pps for Ethernet port
148,800pps for Fast Ethernet port
1,488,000pps for Gigabit Ethernet port

Mac Address

16K MAC address table

Jumbo frame

10KB

Connectors

10/100TX: 12 x ports M12 4-pole D-coded with Auto MDI/MDI-X function
RS-232 connector: 1 x M12 5-pole A-coded
Power Input connector: 1 x M12 5-pole A-coded
Relay contact: 1 x M12 5-pole A-coded

Network Cable

10Base-T: 2-pair UTP/STP Cat. 3, 4, 5/ 5E/ 6 cable
EIA/TIA-568 100-ohm (100m)
100Base-TX: 2-pair UTP/STP Cat. 5/ 5E/ 6 cable
EIA/TIA-568 100-ohm (100m)
EIA/TIA-568 100-ohm (100m)

LED

Per unit: Power 1 (Green), Power 2 (Green), FAULT (Red)
Ethernet port: Link/Activity (Green), Speed (Green);
R.M. indicator (Green)
PoE (Green)

DI/DO

1 Digital Input (DI):
Level 0: -30~2V / Level 1: 10~30V
Max. input current:8mA
1 Digital Output (DO): Open collector to 80 VDC, 50mA

Operating Humidity

5% ~ 95% (Non-condensing)

Operating Temperature

-40°C~75°C / -40°F~167°F

Storage Temperature

-40°C~85°C / -40°F~185°F

Power Supply

9~36VDC

PoE Budget

80W

PoE pin assignment

M12 port # 1~ # 8 support IEEE 802. 3at/af End-point. Per port provides up to 30W

Power Consumption

Max. 11W

Dimensions

IP54 model: Aluminum case
182mm(W)x180.3mm(H)x77.3mm(D)
IP67 model: Aluminum case
215mm(W)x200mm(H)x76.7mm(D)

Weight

1.3kgs

Installation

IP67 model: DIN Rail** and Wall Mount Design
IP54 model: Wall Mount Design

EMI & EMS

FCC Class A,
CE EN55032 Class A, CE EN55024,
CE EN61000-4-2, CE EN61000-4-3,
CE EN61000-4-4, CE EN61000-4-5,
CE EN61000-4-6, CE EN61000-4-8,
CE EN61000-6-2, CE EN61000-6-4

Stability Testing

EN61373 (Shock and Vibration)

Vehicle Certificate

E13 marking (UN ECE R10)
ITxPT labeled

Verifications & Report

EN 50155:2017,
EN 50121-3-2:2016,
EN 50121-4:2016,
EN 45545-1, EN 45545-2 Fire & Smoke verification

ITxPT function (-IGN model)

Delay Shut Down
Inventory Service
Standby Green Mode

Vehicle Compliance

UN ECE R118

MTBF

685,902hrs (standards: IEC 62380)

Warranty

5 years

Software Specifications

Management

SNMP v1 v2c, v3/ Web/Telnet/CLI

SNMP MIB

RFC 1213 MIBII
RFC 1158 MIBII
RFC 1157 SNMP MIB
RFC 1493 Bridge MIB*
RFC 1573 IF MIB
Partial RFC 1757 RMON
RFC 2674 Q-Bridge MIB*;
LLDP MIB
Private MIB

ITU G.8032

Support ITU G.8032 v2/2012 for Ring protection in less than 20ms for self-heal recovery (basic mode)
Support various ring/chain topologies
Includes train ring, auto ring, basic single ring, enhanced ring, multiple-VLAN ring
Enhanced G.8032 ring configuration with ease
Ring covers multicast on different ports
Train mode for auto coupling ring configuration

PoE Management

  1. PoE Detection to check if PD hangs then restart the PD
  2. PoE Scheduling to On/OFF PD upon routine time table
  3. On/ Off, voltage, current, watts, temperature

POE Off/Timer on ignition standby mode

can ultimate the battery standby time by connecting essential devices

User friendly UI

  1. Auto topology drawing
  2. Topology demo
  3. Auto configuration for G.8032 (auto mode) for single ring
  4. Complete CLI for professional setting

Port Trunk with LACP

LACP Port Trunk: 8 Trunk groups/Maximum 8 trunk members

LLDP

Supports LLDP to allow switch to advise its identification and capability on the LAN

CDP

Cisco Discovery Protocol for topology mapping

Environmental Monitoring

System status for input voltage, current and ambient temperature to be shown in GUI and sent alerting if any abnormal status

VLAN

Port Based VLAN
IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID (Up to 4K, VLAN ID can be assigned from 1 to 4096)
GVRP, QinQ of VLAN, QoS, Protocol based VLAN; IPv4 Subnet based VLAN

Spanning Tree

Supports IEEE802.1d Spanning Tree and IEEE802.1w Rapid Spanning Tree, IEEE802.1s Multiple Spanning Tree 16 MSTI

Quality of Service

The quality of service determined by IPv4 Type of service, IPv4 Differentiated Services Code Points - DSCP

Class of Service

Support IEEE802.1p class of service, per port provides 8 priority queues

QoS by VLAN

Tagged QoS by VLAN for all devices in the network

IP Security

Supports 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder

Login Security

Supports IEEE802.1X Authentication/RADIUS

Port Mirror

Support 3 mirroring types: “RX, TX and Both packet”

Network Security

Support 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder.
802.1X access control for port based and MAC based authentication/MAC-Port binding
Ingress/Egress ACL L2/L3
SSL/ SSH v2 for Management
HTTPS for secure access to the web interface
TACACS+** for Authentication

IGMP

Support IGMP snooping v1, v2, v3; 1024 multicast groups; IGMP router port; IGMP query; GMRP

Static MAC-Port bridge

Static multicast forwarding forward reversed IGMP flow with multicast packets binding with ports for IP surveillance application

Bandwidth Control

Support ingress packet filter and egress packet limit.
The egress rate control supports all of packet type.
Ingress filter packet type combination rules are Broadcast/Multicast/Flooded Unicast packet, Broadcast/Multicast packet, Broadcast packet only and all types of packet.
The packet filter rate can be set an accurate value through the pull-down menu for the ingress packet filter and the egress packet limit.

Flow Control

Supports Flow Control for Full-duplex and Back Pressure for Half-duplex

System Log

Supports System log record and remote system log server

Relay Alarm

Provides one relay output for port breakdown, power fail and alarm
Alarm Relay current carry ability: 1A @ DC24V

Protection

  1. Miss-wiring avoidance
  2. Node failure protection
  3. Loop protection

SNMP Trap

Up to 10 trap stations; trap types including:

  1. Device cold start
  2. Authorization failure
  3. Port link up/link down
  4. DI/DO open/close
  5. Typology change (ITU ring)
  6. Power failure
  7. Environmental abnormal**

DHCP

Provide DHCP Client/ DHCP Server/DHCP Option 82/Port based DHCP; DHCP Option 66; basic IPv6 DHCP server

Mac based DHCP Server

Assign IP address by Mac that can include dumb switch in DHCP network

DNS

Provide DNS client feature and support Primary and Secondary DNS server

SNTP

Supports SNTP to synchronize system clock in Internet

Firmware Update

Supports TFTP firmware update, TFTP backup and restore; HTTP firmware upgrade

MLD Snooping

Support IPv6 Multicast stream

Diagnostic

Support Ping, ARP table and DDM information

N-Key Configurator**

RJ45 dongle for firmware upgrade, auto / editable configuration backup/restoration

Configuration
upload and download

Supports editable configuration file for system quick installation

*Future release
**Optional

DIMENSION

IP67 model

IP54 model

ORDERING INFORMATION

All model packages include M12 caps and wall mount bracket. All standard models are non-coating, optional coating models are available with –C model name. Optional TACACS+ models are available with -TAS model names. Optional bypass models are available with –BT/BBT model name. (only on IP67 version)

P/N Model name Description
8360-7309-I
 
IPES-5408T-D-67-24V-IGN 12 10/100TX D-coded w/8 PoE at/af M12 IP67 L2+ Managed Ethernet Switch; -40°C to 75°C; dual 9~36VDC w/ignition w/galvanic isolation
8360-7308-I
 
IPES-5408T-D-54-24V-IGN 12 10/100TX D-coded w/8 PoE at/af M12 IP54 L2+ Managed Ethernet Switch; -40°C to 75°C; dual 9~36VDC w/ignition w/galvanic isolation
8360-73091
 
IES-5408T-D-67-24V-IGN 12 10/100TX D-coded IP67 L2+ Managed Ethernet Switch; -40°C to 75°C; dual 9~36VDC w/ignition
8360-73081
 
IES-5408T-D-54-24V-IGN 12 10/100TX D-coded IP54 L2+ Managed Ethernet Switch; -40°C to 75°C; dual 9~36VDC w/ignition
8850-100 N-key Configurator RJ45 connector dongle for firmware upgrade, auto/editable configuration backup and restoration; -20°C to 60°


OPTIONAL ACCESSORIES - Connector

Model name Description
ECONM12-05A(M)-C-180 5 pin M12 (Male) A-coded 180 degree crimp type connector for DI/DO
ECONM12-08X(M)-SPEEDCON 8 pin M12 (Male) X-coded 180 degree crimp type connector for data, Ethernet CAT6A (10G), shielded, SPEEDCON
ECONM12-04D(M)-C-180 4 pin M12 (Male) D-coded 180 degree crimp type connector for data


OPTIONAL ACCESSORIES - Cable

Model name Description
ECONM12-5P(F)70CM CABLE 5 pin M12 (Female) A-coded 90 degree cable for power supply, 70cm
ECABM12X83MSTP 8 pin M12 (Male) X-coded 180 degree RJ45 STP cable for data, shielded, 300cm
ECAB124030MJS 4 pin M12 (Male) D-coded 180 degree RJ45 STP cable for data, 300cm
ECONM12-05A(F) to MCP 6P-20CM CABLE 5 pin M12 (Female) A-coded 180 degree to 6 pin MCP power cable, 20cm (For ignition models)