IPES-3424DSFP-2P-PT│Industrial IEC 61850-3 PT Ethernet Switches│Lantech®

24 10/100TX PoE + 4 DualSpeed SFP IEC 61850-3 Managed Ethernet Switch w/ Enhanced Ring & MMS

Compliant with IEC61850-3 & IEEE1613

Support dual power redundancy AC&DC

Built-in MMS server based on IEC61850-90-4 switch data modeling for SCADA with monitoring and control

Support IEEE802.3at/af up to 30W per port

Enhanced G.8032 ring protection < 20ms for single ring. Supports auto mode, enhanced mode, train mode, multi-VLAN and basic mode; Enhanced G.8032 ring covers multicast packets; MSTP 16MSTI /RSTP ; support MRP Ring

Miss-wiring avoidance & node failure protection

User friendly UI, including auto topology drawing; Complete CLI

Support LACP link aggregation, IGMP v3/router port, MLD snooping, DHCP server & DHCP Option82; DHCP Snooping, Port based DHCP distribution, Mac based DHCP server, QoS by VLAN, SSH v2/SSL, HTTPS, INGRESS/EGRESS ACL L2/L3,TACACS+**, QinQ

Protocol based VLAN ; IPv4 Subnet based VLAN

USB port to backup, restore the configuration file and upgrade firmware

Datasheet Hardware Manual
For latest firmware and web UI user manual, please contact us.

OVERVIEW

Lantech IPES-3424DSFP-2P-PT is a high performance L2+ (Gigabit uplink) switch with 24 10/100/1000T w/ 24 PoE 802.3af/802.3at + 4 Dual Speed SFP that complies with IEC 61850-3 & IEEE 1613. It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring while also supports train ring, enhanced mode, multiple VLAN model. The comprehensive QoS, QoS by VLAN, advanced security including INGRESS/EGRESS ACL L2/L3, TACACS+**, SSH v2/SSL, Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port, QinQ are supported and also required in large network.

The built-in MMS server allows SCADA to control & monitor switch for data modeling.

Compliant with IEEE802.3at/af standard, the Lantech IPES-3424DSFP-2P-PT is able to feed each PoE port up to 30Watts@54VDC providing the connected PD devices at 10/100M speed. It also supports advanced PoE management including PoE detection and scheduling. PoE detection can detect if the connected PD still alive then sending power; PoE scheduling is to allow pre-set power feeding schedule upon routine time table. Per port PoE states explicit voltage, current, watt and PoE temperature information.

Built-in MMS server for IEC61850 data modeling for monitoring and control
The built-in MMS (Manufacturing Messaging Specification) server can help SCADA to monitor and control switch by data modeling. It covers system, power, port status, network configuration.

Miss-wiring avoidance, Loop protection, Node failure protection
The IPES-3424DSFP-2P-PT also embedded several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech IPES-3424DSFP-2P-PT is able to alert with the LED indicator and disable ring automatically. Node failure protection ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. This feature prevents the broken ring and keep ring alive without any re-configuration needed. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.

Enhanced G.8032 ring, 16 MSTI MSTP; MRP ring
Lantech IPES-3424DSFP-2P-PT features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering Multicast packets. It also supports various ring topologies that covers double ring, multi-chain (under enhanced ring), train ring, basic ring, multiple-VLAN ring and auto-ring by easy setup than others. The innovative auto-Ring configurator (auto mode) can calculate owner and neighbor in one step. It supports MSTP that allows RSTP over VLAN for redundant links with 16 MSTI.

MRP (Media Redundancy Protocol) can be supported for industrial automation networks.

DHCP option 82 & Port based, Mac based DHCP, Option66, DHCP Snooping, IPv6 DHCP server
DHCP server can assign dedicated IP address by MAC or by port (Port based for single switch) , it also can assign IP address by port for multiple switches with single DHCP option82 server. DHCP Snooping is supported. For the ending device which need to download file from TFTP server, DHCP Option66 server can offer IP address of TFTP server to DHCP client. Basic IPv6 DHCP service can be supported.

QoS by VLAN for legacy devices
QoS by VLAN can allow switch to tag QoS by VLAN regardless the devices acknowledge QoS or not in which greatly enhance the bandwidth management in a network.

QinQ, QoS and GVRP supported
It supports the QinQ, QoS, GVRP for large VLAN segmentation.

802.1X security by MAC address
MAC-based port authentication is an alternative approach to 802.1x for authenticating hosts connected to a port. By authenticating based on the host's source MAC address, the host is not required to run a user for the 802.1x protocol. The RADIUS server that performs the authentication will inform the switch if this MAC can be registered in the MAC address table of switch.

IGMPv3,GMRP, router port, MLD Snooping, static multicast forwarding and multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP, router port, MLD snooping and static multicast forwarding binding by ports for video surveillance application.

Auto-provisioning for firmware/configuration update
The switch supports auto-provisioning for switch to auto-check the latest software image and configuration through TFTP server.

User friendly UI, Auto topology drawing, complete CLI
The user friendly UI, innovative auto topology drawing and topology demo makes IPES-3424DSFP-2P-PT much easier to get hands-on. The IPES-3424DSFP-2P-PT supports DMI interface that can correspond with DDM SFPs (Digital diagnostic monitor) to display the five parameters in Lantech’s UI, including optical output power, input power, temperature, laser bias current and transceiver supply voltage***. The TX power/RX power raw data is automatically converted to dB values for installer, making it easier to calculate the fiber distance. The complete CLI enables professional engineer to configure setting by command line.

Editable configuration file; USB port for configuration upload & download
The configuration file of Lantech IPES-3424DSFP-2P-PT can be exported and edited with word processor for the other switches configuration with ease. The factory reset button can restore the setting back to factory default and built-in watchdog design can automatically reboot the switch when CPU is found dead.

The built-in USB port can have configuration upload & download by USB dongle.

Event log & message; 2 DI / 2 DO
In case of event, the IPES-3424DSFP-2P-PT is able to send an email to pre-defined addresses as well as SNMP Traps our immediately. It provides 2 DI and 2 DO. When disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the alarm while sending alert information to IP network with email and traps.

Various dual power conversions redundancy; Relay contact alarm
Lantech IPES-3424DSFP-2P-PT supports dual power redundancies with isolated 100~240VAC/120~370VDC power conversion and isolated 36~75VDC power conversion or with non-isolated 12~56VDC power module to increase the network reliability. It also supports terminal block for connecting DC 48V PoE power source. Featured with relay contact alarm function, the IPES-3424DSFP-2P-PT is able to connect with alarm system in case of power failure. The IPES-3424DSFP-2P-PT also provides 4kV EFT, ±4kV Surge and ±15kV ESD air protection, which can reduce unstable situation caused by power line and Ethernet.

Industrial hardened design for extended temperature operation
Lantech IPES-3424DSFP-2P-PT features high reliability and robustness withstanding extensive EMI/RFI phenomenon, lighting surge, inductive load switching, high ESD, high fault current, environmental vibration and shocks usually found in factory, substation, steel automation, aviation, mining and process control. It is the best solution for Automation, transportation, surveillance, Wireless backhaul, Semi-conductor factory and assembly lines.

Lantech IPES-3424DSFP-2P-PT can run under widely operational temperature (-40°C~75°C) in the harsh environment.

Future Release
Optional
Optional DDM SFP required

FEATURES

24 10/100TX 802.3af/at POE + 4 Dual Speed SFP (Total 28 Ports Switch)
Back-plane (Switching Fabric): 12.8Gbps
16K MAC address table
Built-in MMS server for SCADA data-modeling with control and monitoring
- System info
- Power
- Device event report
- Port status
- Port statistic
- Port event report
- Firmware upgrade
- Network configuration
Embedded 24 PoE ports IEEE802.3af/at function to feed power up to 30W@54V; 15W @ 48V per port for active operation
Dual isolated power conversions for 1600V DC(36V~75V)
Dual isolated power conversions for ±3000 V (100V~240VAC/120V~370VDC)
Dual power supply terminal block for non-isolated power DC(12V~56V)
Rear terminal block for PoE power source(DC48V)
PoE management including PoE detection and scheduling for PD (power devices)
10KB Jumbo frame
User friendly UI, Auto topology drawing, topology demo, Complete CLI for professional setting
Enhanced G.8032 Ring recovery < 20ms in single ring
- Support various ring/chain topologies, including train ring, enhanced ring, basic ring, auto ring & multiple VLAN ring
- Enhanced G.8032 ring configuration with ease
- Auto ring configuration(auto mode) for single ring
- Covers multi-cast and data packets
DDM to support SFP diagnostic function***
- Automatically convert the raw data into dB values for TX power/RX power, making it easier to measure the fiber distance
Provides 4kV EFT protection
Provides ±8kV (Contact) and ±15kV (Air) ESD protection
Provides ±4kV Surge protection
Supports IEEE 802.1p Class of Service, per port provides 8 priority queues Port base, Tag Base and Type of Service Priority
IEEE 802.1d STP, IEEE 802.1w RSTP,802.1s MSTP VLAN redundancy with 16 MSTI
4K 802.1Q VLAN, Port based VLAN, GVRP, QinQ
Supports IEEE 802.1ab LLDP, Cisco CDP; LLDP info can be viewed via Web/ Console
DHCP server / client / DHCP Option 82 relay / DHCP Option 82 server; Port based DHCP server; DHCP Snooping; DHCP Option 66; basic IPv6 DHCP server
Mac based DHCP server to assign IP address
MLD Snooping for IPv6 Multicast stream
Bandwidth Control
- Ingress packet filter and egress rate limit
- Broadcast/multicast packet filter control
Relay alarm output system events
Miss-wiring avoidance
- LED indicator
Node failure protection
- Ensure the switches in a ring to survive after power breakout is back
- The status can be shown in NMS when each switch is back
TFTP/HTTP firmware upgrade
Configuration backup and restoration
- Supports text configuration file for system quick installation
- USB port for upload / download configuration by USB dongle
System Event Log and SNMP Trap for alarm support; 32 RMON counters
Security
- SSL/SSH v2/INGRESS/EGRESS ACL L2/L3
- MAC address table: MAC address entries/Filter/MAC-Port binding
- IP Security: IP address security management to prevent unauthorized intruder.
- Login Security: IEEE802.1X/RADIUS
- HTTPS for secure access to the web interface
- TACACS+**
Static multicast forwarding forward reversed IGMP flow with multicast packets binding with ports for IP surveillance application
IGMP router port to assign query in ring for reversed multicast video flow
IGMPv1,v2,v3 with Query mode for multimedia; GMRP
Factory reset button to restore setting to factory default
Watchdog design to auto reboot switch CPU is found dead
Diagnostic including Ping / DDM information
Supports DIDO (2 Digital Input / 2 Digital Output)
IP30 metal housing with DIN rail and Wall-mount** design
Auto Provision to verify switch firmware with the latest or certain version

Future Release
Optional
Optional DDM SFP required

SPECIFICATIONS

Hardware Specifications

IEEE Standards

IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Ethernet
IEEE 802.3ab 1000Base-T Ethernet
IEEE 802.3z Gigabit Fiber
IEEE 802.3x Flow Control Capability
ANSI/IEEE 802.3 Auto-negotiation
IEEE 802.1Q VLAN
IEEE 802.1p Class of Service
IEEE 802.1X Access Control
IEEE 802.1D Spanning Tree
IEEE 802.1w Rapid Spanning Tree
IEEE 802.1s Multiple Spanning Tree
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
IEEE 802.1x User Authentication (Radius)
IEEE 802.3t/af Power Over Ethernet

Switch Architecture

Back-plane (Switching Fabric): 12.8Gbps

Transfer Rate

14,880pps for Ethernet port
148,800pps for Fast Ethernet port
1,488,000pps for Gigabit Ethernet / Gigabit Fiber port

MAC Address

16K MAC address table

Jumbo frame

10KB

PoE pin assignment

RJ-45 port # 1~# 24 support PoE at/af End-point,
Alternative A mode. Per port provides up to 30W@54V capability.
Positive (VCC+): RJ-45 pin 1,2.
Negative (VCC-): RJ-45 pin 3,6.

PoE input voltage & Power feed voltage

Input V	Active Mode A /Output V
45~56V(af)	48V@15W
54~56V(at)	54V@30W

Connectors

24 10/100TX RJ-45 with auto MDI/MDI-X function
4 100M / 1000M Mini-GBIC : SFP sockets
RS-232 console: Female DB-9
USB for configuration restore/backup

LED

Per unit: Power 1 (Green), Power 2 (Green), Alarm (Red) ,R.M (Green)
Link/Activity (Green), Full duplex/collision(Yellow)), MINI GBIC (Link/Activity )(Green)

Power Supply

Two power sockets for switch system,
12~56VDC input
IEC320 100~240VAC conversion (-AC model)
AC/DC 100~240VAC/120~370VDC conversion (-HV model)
48VDC for PoE

Power Consumption

Full load: 30W/ Unload: 13W

PoE Power Budget

Max 720W (from separate PoE power supply) (50-56VDC input is recommended for 802.3at 30W applications)
Higher PoE budget can be applied upon request. **

Relay Alarm

Provides one relay output for port breakdown, power fail and alarm.
Alarm Relay current carry ability: 1A @ DC24V

DI/DO

2 Digital Input (DI) :
Level 0: -30~2V / Level 1: 10~30V
Max. input current:8mA
2 Digital Output(DO): Open collector to 40 VDC, 200mA

Factory reset button & watch dog design

Factory reset button to restore back to factory default settings. Watch dog design can reboot switch automatically when CPU is found dead

Case Dimension

19” Metal case,IP-30; 440mm(W)x325mm(D)x44mm(H)

Weight

2.9 kgs

Operating Humidity

5%~95% (Non-condensing)

Operating Temperature

Extended temperature : -40°C ~75°C

Storage Temperature

-40°C ~85°C

EMI & EMS

FCC Class A,
CE EN55032 Class A, CE EN55024,

	IEC 61850-3	IEEE 1613
IEC 61000-4-2 ESD	Contact: ±6 kV; Air: ±8 kV	Contact: ±8 kV; Air: ±15 kV
IEC 61000-4-3 RS	80 to 3000 MHz: 10 V/m	80 to 1000 MHz: 20 V/m
IEC 61000-4-4 EFT	220VAC: Power: 4 kV; Signal: 4 kV 48VDC: Power: 4 kV
IEC 61000-4-5 Surge	DC power: Line to line: ±1 kV; Line to earth: ±2 kV AC power: Line to line: ±2 kV; Line to earth: ±4 kV Signal: Line to line: ±2 kV; Line to earth: ±4 kV
IEC 61000-4-6 CS	220VAC: Power: 10V; Signal: 10V 48VDC: Power: 10V

IEC 61000-4-8 PFMF
CE EN61000-6-2, CE EN61000-6-4,
CE EN61000-6-5

Safety

EN IEC 62368-1

Stability Testing

IEC60068-2-32 (Free fall), IEC60068-2-27 (Shock), IEC60068-2-6 (Vibration)

Power Automation

IEC 61850-3, IEEE 1613, IEC 60255-5

MTBF

529,901 Hrs
(standards: IEC 62380)

Warranty

5 years

Software Specifications

Management	SNMP v1 v2c, v3/ Web/Telnet/CLI
SNMP MIB	MIB MIBII SNMP MIB Bridge MIB IF MIB RMON MIB Private MIB
VLAN	Port Based VLAN IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID (Up to 4K, VLAN ID can be assigned from 1 to 4096) GVRP, QinQ, Protocol based VLAN; IPv4 Subnet based VLAN
Port Trunk with LACP	LACP Port Trunk: 8 Trunk groups
LLDP	Support LLDP to allow switch to advise its identification and capability on the LAN
CDP	Cisco Discovery protocol for topology mapping
ITU G.8032	Support ITU G.8032 v2/2012 for Ring protection in less than 20ms for self-heal recovery (single ring enhanced mode) Support various ring/chain topologies Includes train ring, auto ring, basic single ring, enhanced ring, multiple-VLAN ring Enhanced G.8032 ring configuration with ease Cover multicast & data packets protection
User friendly UI	Auto topology drawing Topology demo DDM threshold monitoring with dB values*** Complete CLI supported
PoE Management	PoE Detection to check if PD is hang up then restart the PD PoE Scheduling to On/OFF PD upon routine time table Per-port PoE status including current, voltage, watt and temperature
Spanning Tree	Supports IEEE802.1d Spanning Tree and IEEE802.1w Rapid Spanning Tree, IEEE802.1s Multiple Spanning Tree 16 MSTI
Quality of Service	The quality of service determined by port / CoS / ToS / VLAN / 61375-3-4
Class of Service	Support IEEE802.1p class of service, per port provides 8 priority queues
MLD Snooping	Support IPv6 Multicast stream
Port Mirror	Support 3 mirroring types: “RX, TX and Both packet”
IGMP	Support IGMP snooping v1,v2,v3; Supports IGMP static route; 1024 multicast groups; IGMP router port ; IGMP query; GMRP
Static MAC-Port Bridge	Static multicast forwarding forward reversed IGMP flow with multicast packets binding with ports for IP surveillance application
Bandwidth Control	Support ingress packet filter and egress packet limit. The egress rate control supports all of packet type, the limit rates are 0~100Mbps. Ingress filter packet type combination rules are Broadcast/Multicast/Flooded Unicast packet, Broadcast/Multicast packet, Broadcast packet only and all types of packet. The packet filter rate can be set from 0 to 100Mbps The packet filter rate can be set an accurate value through the pull-down menu for the ingress packet filter and the egress packet limit.
Network Security	Support 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder. 802.1X access control for port based and MAC based authentication/MAC-Port binding Management access control with priority Ingress/Egress ACL L2/L3 SSL/ SSH v2 for Management HTTPS for secure access to the web interface TACACS+** for Authentication
Flow Control	Support Flow Control for Full-duplex and Back Pressure for Half-duplex
Protection	Miss-wiring avoidance node failure protection Loop protection
System Log	Support System log record and remote system log server
SNMP Trap	Up to 10 trap stations; trap types including: Device cold start Authorization failure Port link up/link down DI/DO open/close Typology change(ITU ring) Power failure Environmental abnormal
DHCP	Provide DHCP Client/ DHCP Server/DHCP Option 82/Port based DHCP; DHCP Snooping; DHCP Option 66; basic IPv6 DHCP server
Mac based DHCP Server	Assign IP address by Mac
DNS	Provide DNS client feature
Diagnostic	Support Ping and DDM information
SNTP	Support SNTP to synchronize system clock in Internet
Environmental Monitoring	Internal sensor to detect temperature, voltage and current and send SNMP traps and emails if any abnormal events
Factory reset button & watch dog design	Factory reset button to restore back to factory default settings. Watch dog design can reboot switch automatically under certain circumstances
Firmware Update	Supports TFTP firmware update, TFTP backup and restore; HTTP firmware upgrade
USB Configuration backup and restore	Supports text editable configuration file for system quick installation to backup and restore USB dongle for automatic back up and editable restore
Auto Provision	To verify switch firmware with the latest or certain version

Future Release
Optional
Optional DDM SFP required

DIMENSION

ORDERING INFORMATION

For optional power supply, add +DC, +DCI, +AC, or +HV to the part number.

P/N	Model name	Description
8388-602	IPES-3424DSFP-2P-PT	24 10/100TX POE at/af + 4 Dual SFP IEC61850-3 Managed Ethernet Switch w/ Enhanced Ring & MMS w/ One DC 12~56VDC power module + 1x optional power socket + 1x 48VDC PoE power input; -40°C to 75°C
8388-604	IPES-3424DSFP-2P-PT-AC	24 10/100TX POE at/af + 4 Dual SFP IEC61850-3 Managed Ethernet Switch w/ Enhanced Ring & MMS w/ One isolated AC100~240VAC IEC320 power conversion + 1x optional power socket + 1x 48VDC PoE power input; -40°C to 75°C
8388-605	IPES-3424DSFP-2P-PT-HV	24 10/100TX POE at/af + 4 Dual SFP IEC61850-3 Managed Ethernet Switch w/ Enhanced Ring & MMS w/ One isolated AC/DC 100~240VAC/120~370VDC power conversion + 1x optional power socket + 1x 48VDC PoE power input; -40°C to 75°C

OPTIONAL ACCESSORIES - Power for System

Model name	Description
EOTH000701	Isolation Power 100-240VAC, 120-370VDC 2.0A max, 47-63HZ
EOTH000702	Isolation Power 36-75VDC, 2.5A
EOTH000703	Isolation Power 100-240VAC IEC320 socket, 2.0A max, 47-63HZ
EOTH000704	Power Input Module 12-56VDC, 2.5A

OPTIONAL ACCESSORIES - DIN Rail Power

Model name	Description
NDR-480 Series	480W Single Output Industrial Din Rail Power; 90-264VAC / 127-370VDC Input Range; Cooling by free air convection; RoHS2 ; Operating Temp. -20°C~70°C (ambient, derating each output at 2.5% per degree from 50°C ~ 70°C)
NDR-240 Series	240W Single Output Industrial Din Rail Power; 90-264VAC / 127-370VDC Input Range; Cooling by free air convection; RoHS2 ; Operating Temp. -20°C~70°C (ambient, derating each output at 2.5% per degree from 50°C ~ 70°C)
NDR-120 Series	120W Single Output Industrial Din Rail Power; 90-264VAC / 127-370VDC Input Range; Cooling by free air convection; RoHS2 ; Operating Temp. -20°C~70°C (ambient, derating each output at 2.5% per degree from 50°C ~ 70°C; For 115VAC, please refer to derating curve on NDR-120 Series datasheet)
NDR-75 Series	75W Single Output Industrial Din Rail Power; 90-264VAC / 127-370VDC Input Range; Cooling by free air convection; RoHS2 ; Operating Temp. -20°C~70°C (ambient, derating each output at 2.5% per degree from 50°C ~ 70°C; For 115VAC, please refer to derating curve on NDR-120 Series datasheet)

OPTIONAL ACCESSORIES - Mini GBIC (SFP)

Model name	Description	Model name	Description
8330-162-V1	MINI GBIC 1000SX (LC/0.5KM) Transceiver	8330-186-V1	1.25Gbps BiDi SFP 20KM Transceiver (WDM 1310)
8330-163-V1	MINI GBIC 1000SX2 (LC/2KM) Transceiver	8330-187-V1	LTSFP-1000BX-20KM Transceiver (WDM 1550)
8330-165-V1	MINI GBIC 1000LX (LC/10KM) Transceiver	8330-180-V1	LTSFP-1000BX-40KM Transceiver (WDM 1310)
8340-0591-V1	MINI GBIC 1000LHX (LC/40KM) Transceiver	8330-182-V1	LTSFP-1000BX-40KM Transceiver (WDM 1550)
8330-166-V1	MINI GBIC 1000XD (LC/50KM) Transceiver	8330-181-V1	LTSFP-1000BX-60KM Transceiver (WDM 1310)
8330-169-V1	MINI GBIC 1000XD (LC/60KM) Transceiver	8330-183-V1	LTSFP-1000BX-60KM Transceiver (WDM 1550)
8330-167-V1	MINI GBIC 1000ZX (LC/80KM) Transceiver	8330-184-V1	LTSFP-1000BX-80KM Transceiver (WDM 1490)
8330-170-V1	MINI GBIC 1000EZX (120KM) Transceiver	8330-185-V1	LTSFP-1000BX-80KM Transceiver (WDM 1550)
8330-168-V1	MINI GBIC 10/100/1000T (100m) Transceiver	8330-071-V1	125Mbps BiDi SFP 2KM (WDM 1310) Transceiver
8330-060-V1	100Base FX 2KM, Multi-mode, LC Transceiver	8330-072-V1	125Mbps BiDi SFP 2KM (WDM 1550) Transceiver
8330-065-V1	100Base FX 5KM, Multi-mode, LC Transceiver	8330-069-V1	125Mbps BiDi SFP 20KM (WDM 1310) Transceiver
8330-061-V1	100Base LX 30KM, Single-mode, LC Transceiver	8330-068-V1	125Mbps BiDi SFP 20KM (WDM 1550) Transceiver
8330-059-V1	100Base LX 60KM, Single-mode, LC Transceiver	8330-080-V1	125Mbps BiDi SFP 40KM (WDM 1310) Transceiver
8330-197-V1	1.25Gbps BiDi SFP 0.5KM Transceiver (WDM 1310)	8330-082-V1	125Mbps BiDi SFP 40KM (WDM 1550) Transceiver
8330-198-V1	1.25Gbps BiDi SFP 0.5KM Transceiver (WDM 1550)	8330-081-V1	125Mbps BiDi SFP 60KM (WDM 1310) Transceiver
8330-195-V1	1.25Gbps BiDi SFP 2KM Transceiver (WDM 1310)	8330-083-V1	125Mbps BiDi SFP 60KM (WDM 1550) Transceiver
8330-196-V1	1.25Gbps BiDi SFP 2KM Transceiver (WDM 1550)	8330-084-V1	125Mbps BiDi SFP 80KM (WDM 1310) Transceiver
8330-188-V1	1.25Gbps BiDi SFP 10KM Transceiver (WDM 1310)	8330-085-V1	125Mbps BiDi SFP 80KM (WDM 1550) Transceiver
8330-189-V1	1.25Gbps BiDi SFP 10KM Transceiver (WDM 1550)	8330-191-V1	Dual Speed SFP 100M/1000M-LX 10KM Transceiver
		All SFP P/N# ended with D are with DDM function

Hardened Ethernet Connections

Hardened Routers

Indoor Rackmount / PoE / Fiber

Software / Accessories

Naming Rule

24 10/100TX PoE + 4 DualSpeed SFP IEC 61850-3 Managed Ethernet Switch w/ Enhanced Ring & MMS

OVERVIEW

Future Release
Optional
Optional DDM SFP required

FEATURES

Future Release
Optional
Optional DDM SFP required

SPECIFICATIONS

Hardware Specifications

Software Specifications

Future Release
Optional
Optional DDM SFP required

DIMENSION

ORDERING INFORMATION

OPTIONAL ACCESSORIES - Power for System

OPTIONAL ACCESSORIES - DIN Rail Power

OPTIONAL ACCESSORIES - Mini GBIC (SFP)

About Lantech

Taiwan Quality

Contact Us

Hardened Ethernet Connections

Hardened Routers

Indoor Rackmount / PoE / Fiber

Software / Accessories

Naming Rule

IPES-3424DSFP-2P-PT

24 10/100TX PoE + 4 DualSpeed SFP IEC 61850-3 Managed Ethernet Switch w/ Enhanced Ring & MMS

OVERVIEW

*Future Release**Optional***Optional DDM SFP required

FEATURES

*Future Release**Optional***Optional DDM SFP required

SPECIFICATIONS

Hardware Specifications

Software Specifications

*Future Release**Optional***Optional DDM SFP required

DIMENSION

ORDERING INFORMATION

OPTIONAL ACCESSORIES - Power for System

OPTIONAL ACCESSORIES - DIN Rail Power

OPTIONAL ACCESSORIES - Mini GBIC (SFP)

About Lantech

Taiwan Quality

Contact Us

Future Release
Optional
Optional DDM SFP required

Future Release
Optional
Optional DDM SFP required

Future Release
Optional
Optional DDM SFP required